Mirror Defogger

 



Download E - catalog



MAX INC DGU electric mirror defogger which is widely used in bathroom mirror decoration of hotels, restaurants, villas, service apartments, and residential buildings.


When a MAX INC electric mirror defogger is applied to any normal mirror the result is a crystal clear, fog free mirror.


All of MAX INC defoggers are manufactured under ISO-9001 system control, Our defoggers are CE, UL, PSE, SAA, RoHS, IP54 approved.


We all know the problem, it's an everyday issue, step out from the shower or bath, and you find your bathroom mirror is steamed up and usually you have to wipe away the condensation with a towel or your hand. Well there is a solution!

MAX INC mirror defoggers (synonymous with mirror heater, mirror heating pads, demisting pads) provide just a nice bit of comfort in the Shower Area


WORKING PRINCIPLE

MAX INC mirror defoggers are backed with adhesive heating pads, and is installed onto the back of mirror. They provide heat, which transfers directly to the mirror, resulting in a warming of mirror surface. This gets rid of the mist. So every time you step out from the shower or bath, you no longer have to wait for the mist to clear before shaving, drying your hair or putting make up on.



TECHNICAL PARAMETERS

  • Voltage T2V-24V, 120V-240V
  • Input power: 2.0-2.5w/d m2
  • Double insulated layers with Self-adhesive backing
  • Average Temperature Rise: 15-18°C
  • Thickness: 0.4mm


  • FEATURES

  • Safe to use, (CE, UL approval)
  • Safe to use(CE, UL approval)
  • Low cost
  • Temperature is self-regulating


  • OTHER ADVANTAGES OVER NORMAL MIRRORS

    Prevents moisture damage to silver coatings Retains mirror in the place in the event of breakage Reduces need for cleaning



    Standard models

    Shape: Rectangular
    Code Size Power rating(watt) Energy consumption
    (kw.h)
    120V 220V 120V 220V
    R-2432 600mmx800mm (24" X32" ) 96 96 0.096 0.096


    How to select Max Inc. defogger to make a special heated mirror?

    Selecting size of mirror defogger should be based on the mirror size. If you require your entire mirror to be de-misted, then the pad should be the same size as your mirror. If you don't want to have your entire mirror de-misted, but we recommend that our demister pad be no smaller than 60% of your mirror size. Different shapes make no difference in choosing.



    INSTALLATION INSTRUCTION


    Safety points:

  • Defogger is designed to be used as a bathroom mirror defogger only. Install in accordance with these instructions. Any other use is not recommended.
  • Installation is not difficult and conforms to standard industry practice. As with any electrical product, we do recommend installation be performed by a qualified person in accordance
            with local codes. Remember to disconnect power at the fuse breaker panel before installation.
  • The heating element of mirror defogger should never be cut or damaged. This will render the product useless. It cannot be repaired. Please take particular care over this point.
  • However you may trim the product so long as the actual heating element is NOT damaged, which is common for oval and round series.
  • The power supply cable of the defogger should not be pulled or drawn forcefully.


  • FITTING THE HEATER TO THE MIRROR

  • Adhere the heater pad to the back of the mirror, NOT to the wall.
  • Always handle mirrors with care. Lay the mirror face down on a protective cushion/surface.
  • The back of the mirror must be absolutely clean, dry and grease free.
  • Peel off the protection paper first in about 10cm width and fold the paper, adhere the heater with self-backing directly
            onto the back of the mirror, using towel or some other soft rubber to wipe the back of the defogger. In the mean time,
            rip off the protection paper to stick the defogger onto the mirror easily.
  • Ensure that there are no trapped air bubbles and that the heater is positioned where you would like.
  • Properly apply some clear silicon around the mirror Or if the mirror rests on clips, place a layer of silicon on the bottom
            of the clips.
  • Please allow a 2mm gap between the mirror and hard substances (eg ceramic brick, marble, tiles as well as metal and
          wood periphery around mirrors) If you have metal periphery, please ensure the mirror is earthed in line with regulations.



  • ELECTRICAL INSTALLATION INFORMATION

  • Connect the wires of the defogger with the power cord following the electronic standard.
  • We always recommend our heaters are switched with bathroom lights so that it comes on and off with the lights
  • Fix the mirror onto wall by silicon or clips, then apply neutral silicon again to seal around the edge of the mirror, which
            is the same way with normal mirror.
  • Turn on the electricity and test the mirror, about 3-5minuters, the mirror becomes warm and the mist vanishes.